Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

基于合成射流的旋翼翼型动态失速控制研究

针对直升机旋翼工作环境下来流速度和迎角(Angle of attack,AoA)耦合引起的动态失速问题,建立了基于合成射流的旋翼动态失速控制的数值模拟方法。采用运动嵌套网格方法,通过对翼型的平移和旋转实现变来流速度-变迎角的耦合。以积分形式的雷诺平均N-S方程为主控方程,空间离散使用Roe格式,时间离散为隐式LU-SGS方法,以OA209翼型为研究对象,在翼型上表面放置合成射流激振器,开展了射流位置、动量系数、无量纲频率以及偏角等参数对轻度失速、深度失速下翼型动态失速控制的研究。研究发现,轻度失速下,射流位置靠近气流分离点时(20%c附近,c为翼型弦长),对逆压梯度引起的轻度失速控制效果最佳。深度失速下气流分离点虽在5%c之前,但射流位于前缘分离泡后端(10%c附近)时控制效果较好。大迎角需要较大的动量系数才能有效控制。射流频率对涡结构的尺寸和数量会产生一定影响,能改变气动特性波动幅度。较小的射流偏角对轻度失速的控制更有效,而深度失速则需要较大的偏角。     

虚拟环境系统中复杂模型的建立--3D资源在快速开发虚拟环境系统中的应用

对利用3D资源在快速开发虚拟环境系统中的方法进行了研究。在开发虚拟环境系统的过程中，复杂模型的建立是必不可少的，仅仅利用OpenGL函数编程来实现仿真是很困难的，针对该问题提出了利用3D资源进行3D文件读取和转换的两种方案，分析了虚拟环境中复杂模型的建立以及处理的基本方法，并对数控车床的仿真进行了详细介绍。     

Global Response of Martian Plasma Environment to an Interplanetary Structure: From Ena and Plasma Observations at Mars

As a part of the global plasma environment study of Mars and its response to the solar wind, we have analyzed a peculiar case of the subsolar energetic neutral atom (ENA) jet observed on June 7, 2004 by the Neutral Particle Detector (NPD) on board the Mars Express satellite. The “subsolar ENA jet” is generated by the interaction between the solar wind and the Martian exosphere, and is one of the most intense sources of ENA flux observed in the vicinity of Mars. On June 7, 2004 (orbit 485 of Mars Express), the NPD observed a very intense subsolar ENA jet, which then abruptly decreased within ∼10 sec followed by quasi-periodic (∼1 min) flux variations. Simultaneously, the plasma sensors detected a solar wind structure, which was most likely an interplanetary shock surface. The abrupt decrease of the ENA flux and the quasi-periodic flux variations can be understood in the framework of the global response of the Martian plasma obstacle to the interplanetary shock. The generation region of the subsolar ENA jet was pushed towards the planet by the interplanetary shock; and therefore, Mars Express went out of the ENA jet region. Associated global vibrations of the Martian plasma obstacle may have been the cause of the quasi-periodic flux variations of the ENA flux at the spacecraft location.     

Tunnel/predictor display with two-axis control coordination and simplification

A longitudinal-lateral control coordination and simplification concept is considered for a tunnel/predictor display, which presents the command flight path and a specified future aircraft position in a 3-dimensional format to the pilot, for improving flight path control. A basic element of the proposed concept is the generation of common longitudinal-lateral transfer characteristics of the predictor-aircraft system for the crossover frequency region. Control coordination is supported by a dynamics similarity between the longitudinal and the lateral response characteristics of the predictor position in closed-loop pilot control actions. The control coordination and simplification concept is considered to support the pilot in manual flight path control, directed at an enhancement of his control performance and at a reduction of his workload. Results from pilot-in-the-loop simulation experiments support the theoretical findings and show the effectiveness of the proposed predictor concept with control coordination.     

Flutter analysis of an airfoil with bounded random parameters in incompressible flow via Gegenbauer polynomial approximation

The effects of parameter uncertainty on the flutter characteristics of a two-dimensional airfoil in an incompressible flow were investigated through Gegenbauer polynomial approximation. The uncertain parameters, such as the linear and cubic pitch stiffness coefficients are modeled as bounded random variables with λ-PDFs (probability density functions). With the aid of Gegenbauer polynomial approximation, the two-dimensional stochastic airfoil system is transformed at first into its equivalent deterministic one. Then the Hopf-bifurcation point is determined through the equivalent deterministic system, and the onset of the flutter, together with the flutter frequency against the probability density distribution parameter and the intensity of the random variable is explored. In addition, the ranges of the peak pitch and plunge responses against the flight speed and the PDFs of the peak pitch response are obtained. Numerical results show how the probability density distribution parameters and the intensities of random parameters affect the flutter onset speed, flutter angular frequency, the upper and lower boundaries of peak responses, and the PDFs of peak responses.     

基于Pro/E软件的卫星三维建模方法的探讨

主要对基于Pro/E软件的卫星三维建模和高效率、高可靠性、低成本的总装设计方法等进行了初步的研究和探讨。     

逆向工程的关键技术及其研究

综述了逆向工程中实物数字化技术、测量数据的预处理、曲面重建技术、重构曲面的评价和检验等关键技术的发展现状和存在的问题,并对今后的发展方向进行了讨论。